基于PⅢ工控机VI测控系统远程控制研究

虚拟仪器（VI）将计算机采集测试分析引入到电子测量领域，用数字化和软件技术极大地提高了测量的灵活性。而VI远程测控系统是网络技术、通信技术一计算机虚拟技术结合的产物。远程控制技术能够使操作突破地域的限制，已在网络环境下PⅢ工控机上实现。     

大方坯连铸机离线检修设备对中台的改进与完善

介绍了大方坯连铸机离线设备对中台及样规的改进方案.改进后,大大缩短了设备检修时间,降低了工人的劳动强度.     

甲基丙烯酸乙酯合成工艺研究

以大孔强酸性离子交换树脂为催化剂,甲基丙烯酸(MAA)与乙醇直接酯化合成甲基丙烯酸乙酯(EMA)。在MAA与乙醇摩尔比为1:3、反应温度89～93℃、空速0.3h~(-1)的条件下,MAA转化率不低于98％,EMA的选择性不低于99％。     

Colour Centres and Energy Transfer in BaF2-xClx:Eu2+ Phosphors

The optical absorption spectra of BaF2-xClx:Eu2 after ultraviolet (UV) light excitation were investigated.The differences between the absorption spectra after and before excitation (DAS) were observed.The DAS increase at both the high and the low energy side of F band in BaF2-xClx:Eu2 after 245 nm UV light excitation.The bleach effect of UV light and the absorption of electrons in the valence band may account for the former and the formation of Fa centres (association of F(Cl-) centres), whose absorption band matches the HeNe laser better, may explain the latter.In the write-in process, the transfer of electrons is via tunneling.In the readout process, the transfer of electrons captured in F(F-) and Fa centres is more likely via tunneling, and that of F(Cl-) centres is more likely via conduction band.     

沙漠生物结皮土壤发育特征的研究

通过对沙漠生物结皮层相关的土壤特性研究表明,结皮层不仅具有明显的养分富集和细粒物质的聚集作用,而且结皮层腐殖质成份的含量以及其分子结构和复杂程度也在增加。腐殖质光学特性的变化趋势明显反映了不同地区结皮层土壤发育的地带性特征。结皮层持水量明显高于沙层,并对降水再分配有一定影响。     

Frequency shift keyed narrowband interference rejection: optimal exponential weighting factor for the RLS algorithm

Cochannel narrowband interference can limit the performance of direct sequence spread spectrum (DSSS) and high frequency (HF) systems. Narrowband interference (NBI) can be single tone, chirped or frequency shift keyed (FSK) in nature and numerous techniques for its removal have been proposed. Linear adaptive prediction filters based on autoregressive modelling have been suggested owing to their ability to perform in a non-stationary environment. In the FSK narrowband interference case, adaptive filters are susceptible to excess residual errors owing to instantaneous frequency step changes and the finite convergence time required for the filter to adapt to a new interference frequency. The signal degradation owing to this type of interference becomes greater in high SNR regimes and has been found to be a function of the frequency parameters of the FSK interference signal. The paper discusses the convergence and frequency tracking properties of the recursive least squares (RLS) adaptive lattice filter using a posteriori estimation errors in the presence of FSK narrowband interference. An optimal exponential weighting factor that balances convergence time and steady state error is derived for this case of NBI. Results are compared to those of a previously proposed fast converging minimum frequency error (FCMFE) RLS lattice filter.     

A new method for producing high melt strength polypropylene with reactive extrusion

A high‐melt‐strength polypropylene (HMSPP) was prepared using a twin‐screw reactive extruder from a commercial isotactic polypropylene through two stages, first, maleic anhydride is grafted to polypropylene to obtain a maleic anhydride‐grafted polypropylene (PP‐g‐MA), and then the grafted polymer is reacted with epoxy to extend the branched chain. Fourier transformed infrared spectroscopy indicated that maleic anhydride was grafted on polypropylene and reacted with epoxy. Melt flow rate and sag resistance test showed that the melt strength of the HMSPP improved considerably. Differential scanning calorimetry test showed that the long chain branches (LCBs) act as a nucleating agent in the crystallization of the HMSPP, which leads to a high crystallization temperature and crystallinity. Furthermore, the LCB efficiency of the HMSPP can also be calculated by analyzing its rheological property. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers     

Effect of Wall Surface Properties at Different Drying Kinetics on the Deposition Problem in Spray Drying

Current methods in alleviating the wall deposition problem in spray drying emphasize mainly controlling the stickiness of the drying particles and less attention is placed on the properties of the dryer wall. In this experimental study, the effect of wall surface properties on the deposition mechanism has been investigated. Properties considered in classifying different wall materials were surface energy, roughness, and dielectric properties. The model solution contained sucrose, representing low-molecular-weight sugars commonly encountered in spray drying of fruit and vegetable juices. The effect of wall properties on deposition was explored at different drying rates producing particles of different surface rigidity. Larger surface roughness produced higher deposition fluxes for particles with high impact velocity and moisture. Surface energy and surface roughness were found to have no significant effect for dry rigid particles at the middle and bottom elevation of the drying chamber. However, material with lower surface energy (Teflon) exhibited less deposition for rubbery particles at such elevations. Analysis shows that dielectric wall material (Teflon) tends to enhance deposition of dry particles because of attrition at the surface. Higher wall temperature was found to produce slightly more deposition. The results of this work give a general indication of the effect of wall material on the deposition problem and provide the fundamental understanding for further studies along this line. Proper selection of dryer wall material will provide potential alternatives for reducing the deposition problem.     

基于遗传算法的土钉支护结构优化设计研究

通过建立三维有限元模型,对土钉支护的变形和受力性能进行分析,得出土钉力的合理分布。在此基础上,考虑土钉支护的水平位移,采用遗传算法,对土钉支护的结构优化设计进行研究,建立了土钉支护结构的优化设计数学模型,并编制了相应的计算程序。通过算例分析,并与基于极限平衡分析的优化结果相比较,得出合理的土钉支护结构设计的参考结论。